Questions? Call Us: 336-485-6199

Loading...

Netbell-H30-709 POE-IP Horn Speaker 30W

$438.00

A 30W PoE-IP horn speaker that delivers clear audio in high-noise industrial and outdoor areas. One network cable carries both power and audio, and it integrates with IP call stations, intercoms, and the Netbell-NTG for paging, break bells, and emergency alerts.

Overview

The Netbell-H30-709 is a PoE-powered IP horn speaker built for high-noise industrial environments – manufacturing, warehouses, distribution centers, and outdoor or open areas like transportation centers. It delivers clear voice and tones, and integrates seamlessly with Netbell IP call stations, intercom terminals, and the Netbell-NTG tone generator for break-time signals and emergency notifications. Add a Netbell-AU-711 SIP terminal and you can page from your VoIP phone system too – building a facility-wide IP paging system with no expensive contractors. Leveraging Power over Ethernet, one network cable carries both power and data, for simpler installation and lower cost.

How It Works

  • Mount the horn speaker where you need coverage.
  • Run one network cable to it – PoE carries both power and audio, so there’s no separate wiring or amplifier.
  • Locate the speaker with the free config tool and set it up through any standard web browser.
  • Pair it with an IP microphone, intercom, or Netbell-NTG tone generator to page, schedule bells, and send emergency alerts.

What’s in the Box

  • Netbell-H30-709 PoE-IP horn speaker
  • Mounting bracket and hardware
  • Network: RJ45
  • Transmission Rate: 10/100Mbps
  • IP mode:IPv4/IPv6
  • IP Configuration: Static IP / DHCP
  • Network Protocols: TCP/UDP/ARP/ICMP/DHCP/DNS/IGMP
  • Installation: U-bracket Installation (3 screws)
  • RMS Power: 30 W
  • Housing: Aluminum
  • Dust/Water Protection: IP65
  • Sensitivity: 1 W/1 m: 109±3dB
  • Maximum SPL: 122 dB (Pmax/1 m)
  • Frequency Response: 350Hz ~ 15kHz
  • Power Supply: 12VDC/POE
  • Dimensions (W x H x D): 11 x 10.0 x 10" (246 x 292 x 23 cm)
  • Weight: 5LBS

Important Requirements

To achieve the best audio quality for your IP paging system, we recommend building a dedicated VLAN for this system with network equipment compatible with multicast protocol. Netbell IP paging devices support PoE/PoE+, and a properly configured network infrastructure will ensure a smooth installation.

  • The speakers and the PC running the NACT desktop app must be on the same LAN
  • Network and Switch Requirements:
    • Power over Ethernet (PoE/PoE+) Switch Ports
    • Minimum CAT5 cable with maximum of 100 meters from the device to switch
    • Network switch capacity to handle power loads for all devices
    • Router: Must support IGMP (Internet Group Management Protocol) and PIM (Protocol Independent Multicast)
    • Switch: Must support IGMP snooping

Netbell IP Paging System User Manual 

Netbell IP Paging System User Manual - Preliminary

Network Audio Configuration Tool (NACT)

The NACT desktop app is a free tool to configure your IP speaker systems. It’s only needed for initial setup – once the speakers are grouped, they will work without this app. (Note: The program file is a ZIP file that must be extracted after downloading)

NAConfigTool

Video Tutorials

Netbell IP Paging System Software Configuration Part 1, Prepare the NACT App

Netbell IP Paging System – Setup IP Speakers

Important Requirements

To achieve the best audio quality for your IP paging system, we recommend building a dedicated VLAN for this system with network equipment compatible with multicast protocol. Netbell IP paging devices support PoE/PoE+, and a properly configured network infrastructure will ensure a smooth installation.

  • The speakers and the PC running the NACT desktop app must be on the same LAN
  • Network and Switch Requirements:
    • Power over Ethernet (PoE/PoE+) Switch Ports
    • Minimum CAT5 cable with maximum of 100 meters from the device to switch
    • Network switch capacity to handle power loads for all devices
    • Router: Must support IGMP (Internet Group Management Protocol) and PIM (Protocol Independent Multicast)
    • Switch: Must support IGMP snooping
People Also Love

Related Products

The Netbell-KB-E2M is a compact, self-contained design that was created with ease-of-use in mind. Intended to be an all-in-one solution,...
$1,924.00
An IP-based overhead paging system for schools, and other facilities that can be used for emergency alerts, break time scheduling,...
Price range: $334.00 through $1,319.00
An IP-based overhead paging system for warehouses, factories, schools, and industrial facilities that can be used for emergency alerts, break...
Price range: $334.00 through $1,319.00
A network-enabled, cost-effective industrial paging system designed for manufacturing facilities, distribution centers, and industrial warehouses requiring consistent break timing and...
Price range: $334.00 through $1,319.00
The Netbell-4-4Buz includes everything needed for factories, industrial facilities, warehouses to build a fully automated web-based timed alert system for...
$2,332.00
The Netbell-4-4Bell is a one-stop solution for schools, factories, industrial facilities, warehouses to build a fully automated web-based timed alert...
$1,892.00